Smart DBUS Expansion Module

Smart DBUS Expansion Modules (DM Series)

High-density I/O expansion modules with RS485 communication for distributed data acquisition. Ideal for digital I/O, analog signals, and temperature measurement across multiple nodes.

Typical Protocol: RS485 Modbus RTU (for remote I/O and sensor networks).
Best For
  • Distributed remote I/O via RS485
  • Multi-point temperature monitoring
  • High-channel analog acquisition
  • Long-distance wiring reduction

Usage Guide (How to Use Smart DBUS Modules)

Smart DBUS (DM Series) modules are designed for distributed I/O acquisition via RS485. This guide explains typical wiring, addressing, and commissioning steps for Modbus RTU networks.

1) Network Planning
  • Use RS485 daisy-chain topology (avoid star wiring).
  • Plan each node’s I/O type: DI/DO, AI/AO, Temperature, or Mixed.
  • Reserve unique Modbus slave IDs for each module.
2) Wiring & Termination
  • Connect A(+), B(-), GND according to your RS485 standard.
  • Use twisted-pair cable; keep polarity consistent across all nodes.
  • Add 120Ω termination at the first and last device on the bus.
  • Keep the shield grounded properly to reduce noise.
3) Power & I/O Connection
  • Provide stable 24VDC power to each module.
  • Digital outputs: relay DO for universal loads.
  • Analog inputs: verify whether the model supports V/I or current-only.
  • Temperature: match sensor type (PT100 / NTC / Type K).

Commissioning Steps

  1. Power on the module and confirm status indicators.
  2. Set Modbus parameters: Slave ID, baud rate, parity, stop bits.
  3. From the master (PLC / gateway), read basic registers to confirm communication.
  4. Verify each channel using real signals (DI/DO/AI/AO/Temp).
  5. Lock the configuration and label each node (ID + location).

Common Troubleshooting

  • No response: check A/B polarity, slave ID conflicts, baud rate mismatch.
  • Unstable data: improve grounding/shielding and add termination.
  • Analog reading wrong: confirm signal type (V or mA) and wiring.
  • Temperature errors: verify sensor type and wiring (PT100/NTC/TC).
Best Practice: Install DM modules close to field devices, then use one RS485 trunk back to the control cabinet. This reduces cable cost and improves maintainability for large machines and multi-zone temperature systems.

Quick Filter

Jump to the models you need: Digital I/O, Analog I/O, Temperature, or Mixed high-density combinations.

Tip: If you provide required DI/DO/AI/AO/Temp channel counts and signal type (V/I, PT100, NTC, TC), we can recommend the best DM model for your cabinet layout.

How to Choose a DM Module

  • Digital I/O: DE = Digital Inputs, QR = Relay Outputs, DR = Mixed DI/Relay DO.
  • Analog: AE = Analog Inputs, AQ = Analog Outputs, AM = Combined AI + AO.
  • Temperature: AR = PT100 (RTD), AE-NTC = NTC (10K 3950), AT = Type K thermocouple.
  • Current-only Inputs: Some high-density AE/AM models are current-only (as noted in descriptions).
For distributed I/O: place DM modules near sensors/actuators and connect via RS485 trunk to reduce wiring cost.

All Smart DBUS Expansion Modules (DM Series)

Click the model name to view product details. Models are grouped by category for faster selection.

Category Resource Resource Description
Digital I/O DM DE16-16DI 16 digital inputs
Digital I/O DM QR16-16DQ 16 digital outputs (relay)
Digital I/O DM QR32-32DQ 32 digital outputs (relay)
Digital I/O DM DR16-8DI8DQ 8 digital inputs, 8 digital outputs (relay)
Digital I/O DM DR32-16DI16DQ 16 digital inputs, 16 digital outputs (relay)
Analog I/O DM AE08-8AI 8 analog inputs (supports voltage and current)
Analog I/O DM AE16-16AI 16 analog inputs (current only)
Analog I/O DM AE32-32AI 32 analog inputs (current only)
Analog I/O DM AQ04-4AQ 4 analog outputs (supports voltage and current)
Analog I/O DM AQ08-8AQ 8 analog outputs (supports voltage and current)
Analog I/O DM AM06-4AI2AQ 4 analog inputs, 2 analog outputs (both support voltage and current)
Analog I/O DM AM12-8AI4AQ 8 analog inputs (current only), 4 analog outputs (supports voltage and current)
Temperature DM AR08-8PT100 8 PT100 inputs
Temperature DM AE08-8NTC 8 NTC inputs (10K 3950)
Temperature DM AT08-8TC 8 Type K thermocouple inputs
Mixed DM AE16-8NTC8AI 8 NTC inputs, 8 analog inputs (current only)
Mixed DM AE16-12NTC4AI 12 NTC inputs, 4 analog inputs (current only)
Mixed DM AM06-4NTC2AQ 4 NTC inputs, 2 analog outputs (supports voltage and current)
Mixed DM DR16AM12-8DI8DQ8AI4AQ 8 digital inputs, 8 relay outputs, 8 analog inputs (current only), 4 analog outputs (supports voltage and current)

FAQ

Q: What is Smart DBUS used for?

Smart DBUS modules are designed for distributed data acquisition. Install I/O near the field devices, then transmit signals over RS485 to reduce long-distance wiring.

Q: Which analog modules support voltage and current?

Models like DM AE08-8AI, DM AQ04/AQ08, and DM AM06 support voltage and current. Some high-density AI models are current-only as shown in the descriptions.

Q: Can I mix temperature and analog signals in one module?

Yes. Choose combo models like DM AE16-8NTC8AI, DM AE16-12NTC4AI, or DM AM06-4NTC2AQ.

Need Help Choosing a DBUS Module?

Tell us your required DI/DO/AI/AO/Temperature channels and signal types (V/I, PT100, NTC, Type K). We’ll recommend the best DM modules for your distributed I/O network.

Contact Us